{"id":1517,"date":"2022-02-28T00:00:00","date_gmt":"2022-02-28T00:00:00","guid":{"rendered":"https:\/\/ylu6kzueag.wpdns.site\/news\/overhead-line-fitting\/"},"modified":"2022-02-28T00:00:00","modified_gmt":"2022-02-28T00:00:00","slug":"%e0%a4%93%e0%a4%b5%e0%a4%b0%e0%a4%b9%e0%a5%87%e0%a4%a1-%e0%a4%b2%e0%a4%be%e0%a4%87%e0%a4%a8-%e0%a4%ab%e0%a4%bf%e0%a4%9f%e0%a4%bf%e0%a4%82%e0%a4%97","status":"publish","type":"post","link":"https:\/\/www.yojiuelec.com\/hi\/news\/overhead-line-fitting\/","title":{"rendered":"Method for measuring the thickness of hot-dip galvanized zinc layer"},"content":{"rendered":"<p>Hot-dip galvanizing, also known as hot-dip galvanizing, melts the zinc hot-dip galvanizing ingot at high temperature,<\/p>\n<p>puts some auxiliary materials, and then immerses the metal component in the galvanizing tank, so that a zinc layer is<\/p>\n<p>attached to the metal component. The advantage of hot-dip galvanizing is that its anti-corrosion ability is strong, and<\/p>\n<p>the adhesion and hardness of the galvanized layer are better. The disadvantage is that the price is high, a lot of equipment<\/p>\n<p>and space are required, the steel structure is too large and difficult to put into the galvanizing tank, the steel structure is<\/p>\n<p>too weak, and the hot-dip galvanizing is easy to deform. Zinc-rich coatings generally refer to anti-corrosion coatings<\/p>\n<p>containing zinc powder. Zinc-rich coatings on the market contain one zinc content. Want to know the thickness of zinc<\/p>\n<p>can use the following methods<\/p>\n<p>\u00a0<\/p>\n<p><strong>Magnetic method<\/strong><\/p>\n<p>The magnetic method is a non-destructive experimental method. It is carried out according\u00a0to the\u00a0requirements of<\/p>\n<p>GB\/T 4956. It is a method of measuring the thickness of the zinc layer by using an electromagnetic\u00a0thickness gauge.<\/p>\n<p>It is worth mentioning here that the cheaper the equipment may be, the greater the error may be\u00a0measured. The price<\/p>\n<p>of thickness gauges ranges from thousands to tens of thousands, and it is recommended to use\u00a0good equipment for testing.<\/p>\n<p>\u00a0<\/p>\n<p><strong>weighing method<\/strong><\/p>\n<p>According to the requirements of GB\/T13825, the weighing method is an arbitration method. The plating amount of<\/p>\n<p>the zinc coating measured by this method should be converted into the thickness of the coating according to the density<\/p>\n<p>of the coating (7.2g\/cm\u00b2). This method is a destructive experimental method. In the case where the number of parts is<\/p>\n<p>less than 10, the purchaser should not reluctantly accept the weighing method if the weighing method may involve<\/p>\n<p>damage to the parts and the resulting remedial costs are unacceptable to the purchaser.<\/p>\n<p>\u00a0<\/p>\n<p><strong>Anodic dissolution coulometric method<\/strong><\/p>\n<p>Anode-dissolving a limited area of the coating with a suitable electrolyte solution, the complete dissolution of the<\/p>\n<p>coating is determined by the change in the cell voltage, and the thickness of the coating is calculated from the amount<\/p>\n<p>of electricity (in coulombs) consumed by the electrolysis, using the time to dissolve the coating and the Power<\/p>\n<p>consumption, calculate the thickness of the coating.<\/p>\n<p>\u00a0<\/p>\n<p><strong>Cross-sectional microscopy<\/strong><\/p>\n<p>Cross-sectional microscopy is a destructive experimental method and only represents a point, so it is not commonly<\/p>\n<p>used, and is carried out in accordance with GB\/T 6462. The principle is to cut a sample from the workpiece to be tested,<\/p>\n<p>and after inlaying, use appropriate techniques to grind, polish and etch the cross-section, and measure the thickness<\/p>\n<p>of the cross-section of the covering layer with a calibrated ruler.<\/p>\n<div><\/div>","protected":false},"excerpt":{"rendered":"<p>Hot-dip galvanizing, also known as hot-dip galvanizing, melts the zinc hot-dip galvanizing ingot at high temperature, puts some auxiliary materials, and then immerses the metal component in the galvanizing tank, so that a zinc layer is atta<\/p>","protected":false},"author":1,"featured_media":934,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[27],"tags":[],"class_list":["post-1517","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"_links":{"self":[{"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/posts\/1517","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/comments?post=1517"}],"version-history":[{"count":0,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/posts\/1517\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/media\/934"}],"wp:attachment":[{"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/media?parent=1517"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/categories?post=1517"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.yojiuelec.com\/hi\/wp-json\/wp\/v2\/tags?post=1517"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}