News
-
The difference between cold shrinkable cable terminal head and heat shrinkable cable terminal head
Compared with the heat-shrinkable cable terminal, the cold-shrinkable cable terminal does not require heating, and after installation, moving or bending will not cause the danger of internal layer separation like heat-shrinkable cable accessories, because the cold-shrinkable cable terminal is ela...Read more -
Bolt Type Tension Clamp Nll Series
Bolt type tension clamp is a kind of tension clamp The strain clamp refers to the hardware used to fix the wire to withstand the tension of the wire and hang the wire to the strain string or the tower. Used for corners, splices, and terminal connections. Spiral aluminum clad steel wire has extrem...Read more -
Bimetallic Lug | Bimetallic Thimble | Best Solution for Cu/Al Connection
bimetallic lug or bimetallic thimble is special type of thimble for connecting aluminum cable with copper bus or copper terminals. In this article, we will discuss the structure and application of bimetallic terminals. Problems with Cu/Al Joint Aluminum oxide layer is formed which ...Read more -
Suspension Anchoring Clamp YJPT/YJPSP/YJCS/YJPS95 series
at is a suspension Anchoring clamp? Suspension Anchoring clamps are accessories designed for hanging or suspending cables or conductors to pole positions. In other cases, the clamp can hang the cable to the tower. Since the cable is directly connected to the conductor, its gauge needs to match t...Read more -
Aerial Cable Clamp JBG Series
JBG series Aerial Cable Clamp are used for LV-ABC lines with insulated neutral messenger. • The Aerial Cable Clamp of an aluminium alloy cast body and self-adjusting plastic wedges which tighten the conductor without insulation damage. • All parts of the clamp are resistant to corrosion, enviro...Read more -
Under what conditions are the insulation piercing connectors used
Insulation piercing connectors is a clamp device used to connect wires and data lines. Insulation piercing connectors are generally used for branching of trunk lines. The feature is that the installation is more convenient and flexible, and branch lines can be made wherever branches need to be m...Read more -
Low Voltage Insulated Piercing Connector
The Low Voltage Insulated Piercing Connector has the advantages of fast branching and no stripping, stable contact with oxidation, pure copper tinned blades, copper and aluminum cables for general use, flame retardant, fireproof and corrosion resistance, etc. The construction and operati...Read more -
Bolt type parallel groove connectors
The bolt-type parallel groove Connectors is made of plate-plate structure and aluminum alloy material. Relying on the fastening pressure of the bolt, the connected wire is fixed in the upper and lower grooved splints to complete the connection, and then transmitted through flat washers and spri...Read more -
Pg Clamp Pricelist
The parallel groove clamp is used for the connection of aluminum stranded wire or steel core aluminum stranded wire of small and medium cross-section and steel stranded wire of overhead lightning protection wire at a position that does not bear tension. It is also used for jumper connection of...Read more -
What kind of clamps are used for cable suspension
Overhang clip-A gold tool that ties the wire and hangs at the end of the overhang insulator string or from the pole tower. The clip is a gold or piece that is secure to the wire. The above definition indicates that “wire clip” can be a separate gold ware, such as trench clip, damping ...Read more -
Opgw Tension Clamp
The manufacturer provides a complete OPGW strain clamp, including strain clamp, pre-twisted wire protection wire, grounding wire and necessary connection fittings. The tension clamp should be of pre-stranded wire type, and should be able to withstand at least 95% of the ultimate tensile strengt...Read more -
Anticorrosion of Stay rod
Introduction The pull stay rod is an important load-bearing metal component used in the pull stay tower, which connects the pull plate, the pull stay and the UT stay clamp. Their common function is to use the pull-up force generated by the pull plate buried in the ground to fix the pole tower o...Read more